Springfree Trampoline R54 Installation (S Model): tgoma

Springfree Trampoline R54 Installation (S Model): tgoma



we are going to turn your trampoline mat into a game controller that's going to allow you to play games with your tablet on your trampoline there's a few key steps that you're gonna have to follow to make sure that it operates as it should let's get into it follow the steps in your manual it should take around 60 minutes for two people to install you need one inside person and one outside person to install quickly and safely remember the rods in your Springfree trampoline are loaded so keep your face away from them at all times it's also important to make sure that no one jumps on the trampoline while you're installing so while we love them keep the kids away as the game system uses sensors to detect the jumpers position on the met the trampoline should be installed so that the mat is level if there is more than 100 millimetres difference from one side to the other you will have to level the trampoline to ensure the system works to play as soon as you've finished installing make sure you have four AAA batteries unpack all your parts and lay them out so you can make sure that you have everything check that you haven't missed any of the small parts now you're ready to get cracking to find the correct position for your controller on the r54 face the door and find the league to the left of it now it's time for your inside person first take the existing nut off you may need to use a spanner to loosen it but at this stage don't take the bolt out put on the controller by placing the curved section around the back of the leg and over the bolt and put the new barrel nut on it it only needs to be finger tight to ensure the controller is firmly mounted put the supplied cable ties through the mounting plate and then around the frame now it's time to install the clips your cables will go through find sensor position 3 and install your first clip in the pocket that's one rod to the left the correct way to install each clip is to slide it into the pocket facing to the left move around the met to the left installing an each pocket but don't install right in front of the sensor mounts continue installing Clips until you reach sensor position 4 carefully cut the cable ties that are currently holding the sensor mount in place now it's time to secure the sensor mounts with the cable ties start at one cable mount and feed your cable ties up the cross and back down through the met your outside person should help make sure they come up and go down through the right holes starting at sensor position 3 fit the sensor at the end of the cable into the cable mount the sensor is keyed so if it doesn't fit the first way you try turn it over and fit again secure the sensor with two cable ties as shown to hold in place your outside person can help by holding the sensor in place as your inside person fastens the cable ties your inside person will move around to the left installing the cable into each cable clip until you reach the next sensor position install the sensor and fasten both cable ties at each sensor mount and then keep going until you get to position B which is next to the controller starting at position 4 repeat all steps again and your second cable should come out at position a now it's time to attach your cable ends to the controller at the yellow tag on the cable tube feed cable a through until it comes out the end do the same with cable B it's important you attach each cable to the correct controller socket connect the cable with the yellow sticker to a and the cable with the white sticker to B once you have attached the cables to the controller open the velcro on the cable tube and wrap it around the rod sitting directly above the controller use two cable tires to attach the top of the cable tube to the cable clips and use the strap to attach the bottom to the controller you're almost done it's simple to build your tablet holder just fit the two rods into the holder and make sure you get them around the right way as shown the rods will click into place and when they're fully inserted you should be able to see the ends of the rods through the slots at the top and if you jiggle them they won't come loose make sure you're in an area that has good Wi-Fi connection you may need to go inside go to either Google Play or the App Store and search for Tacoma download the app open the app and follow the NEP instructions to set up your account fill in the form fields as prompted it's important that you take the time to set up properly now as these settings are the basis of your family's account going forwards find the six digit serial number on the front of your Tacoma installation manual or the side of your packaging into the serial number in the required field this will allow to Goma support staff to easily assist you should you require it at Springfree trampoline we've taken great care to make sure to Gomer is compliant with the relevant child online privacy protection laws now let's head back out to the trampoline to connect your tablet and battery make sure the Bluetooth in your tablet is turned on and install the batteries into your battery pack making sure no one is on the trampoline put your battery pack onto the controller and press the blue button the lights will pulse blue and green open the takoma app on your tablet and wait until the controller slowly flashes blue which confirms the Bluetooth connection is working if you haven't done it earlier you also need to select the trampoline model that is relevant as this will insure the games work properly put your tablet into the holder then install on the net by placing over the top on the opposite side from the door finally before you can get playing you need to help to go more understand where it is on the trampoline you do this by setting the tablet position follow the instructions on your tablet screen which will explain this to you you're done now it's time to get jumping a couple of things to remember make sure you bring your tablet in at night as well as take the tablet holder off as it can get blown away in the wind it's also a good idea to take the battery pack inside when not in use it will be ok if you leave it outside but it won't last as long you've now taken gaming outside and made it active share your pictures with us on Instagram Facebook or email them to us directly and remember to jump safe jump one at a time

One Reply to “Springfree Trampoline R54 Installation (S Model): tgoma”

Leave a Reply

Your email address will not be published. Required fields are marked *